Try 300-430 Exam Valid Dumps with Instant Download Free Updates
300-430 Dumps First Attempt Guaranteed Success
NEW QUESTION # 117
An engineer is configuring multicast for two WLCs. The controllers are in deferent physical locations and each handles around 500 wire clients. How should the CAPWAP multicast group address be assigned during configuration?
- A. Each WLC management address must be in a different multicast group
- B. Both WLCs must be assigned the same multicast group address
- C. Each WLC must be assigned a unique multicast group address
- D. Each WLC management address must be in the same multicast group
Answer: A
NEW QUESTION # 118
A Cisco WLC has been added to the network and Cisco ISE as a network device, but authentication is failing. Which configuration within the network device configuration should be verified?
- A. device ID
- B. device interface credentials
- C. shared secret
- D. SNMP RO community
Answer: C
NEW QUESTION # 119
A wireless engineer has performed a Wireshark capture on an 802.1x authentication process to troubleshoot a connectivity issue.
Which two types of packet does the EAP contain? (Choose two.)
- A. EAP complete
- B. EAP failure
- C. EAP response
- D. EAP reply
- E. EAP request
Answer: C,E
NEW QUESTION # 120
Refer to the exhibit. Which two items must be supported on the VoWLAN phones to take full advantage of this WLAN configuration? (Choose two.)
- A. SIFS
- B. WMM
- C. TSPEC
- D. 802.11e
- E. APSD
Answer: B,D
Explanation:
The 802.11e, WMM, and Cisco Compatible Extension specifications help balance and prevent the overloading of a cell with audio streams. CAC determines whether there is enough channel capacity to start a call; if not, the phone can scan for another channel
https://www.cisco.com/c/en/us/td/docs/wireless/controller/8-1/Enterprise-Mobility-8-1-Design- Guide/Enterprise_Mobility_8-1_Deployment_Guide/Chapter-9.html
NEW QUESTION # 121
What is the Cisco recommended configuration for a Cisco switch port connected to an AP in local mode for optimal voice over WLAN performance with an 8821 wireless phone?
- A. switchport mode access mls qos trust cos
- B. switchport mode access mls qos trust dscp
- C. switchport encapsulation dot1q
switchport mode trunk
mls qos trust device cisco-phone - D. switchport mode access
mls qos trust device cisco-phone
Answer: A
NEW QUESTION # 122
An enterprise has recently deployed a voice and video solution available to all employees using AireOS controllers. The employees must use this service over their laptops, but users report poor service when connected to the wireless network. The programs that consume bandwidth must be identified and restricted. Which configuration on the WLAN aids in recognizing the traffic?
- A. NetFlow Monitor
- B. AVC Profile
- C. Application Visibility
- D. QoS Profile
Answer: C
NEW QUESTION # 123
An IT team is growing quickly and needs a solution for management device access. The solution must authenticate users from an external repository instead of the current local on the WLC, and it must also identify the user and determine what level of access users should have. Which protocol do you recommend to achieve these goals?
- A. RADIUS
- B. TACACS+
- C. network policy server
- D. LDAP
Answer: B
Explanation:
Explanation
https://www.cisco.com/c/en/us/td/docs/switches/lan/Denali_161/ConfigExamples_Technotes/Techzone_Articles
https://community.cisco.com/t5/wireless-mobility-documents/wlc-and-acs-5-x-tacacs-configuration-example-we
NEW QUESTION # 124
Refer to the exhibit.
A network administrator deploys the DHCP profiler service in two ISE servers: 10.3.10.101 and 10.3.10.102. All BYOD devices connecting to WLAN on VLAN63 have been incorrectly profiled and are assigned as unknown profiled endpoints. Which action efficiently rectifies the issue according to Cisco recommendations?
- A. Nothing needed to be added on the Cisco WLC or VLAN interface. The ISE configuration must be fixed.
- B. Disable DHCP proxy on the Cisco WLC.
- C. Disable DHCP proxy on the Cisco WLC and run the ip helper-address command under the VLAN interface to point to DHCP and the two ISE servers.
- D. Keep DHCP proxy enabled on the Cisco WLC and define helper-address under the VLAN interface to point to the two ISE servers.
Answer: C
NEW QUESTION # 125
An engineer configures Cisco CMX. which uses Layer 2 high availability on primary and secondary CMX instances, according to these specifications:
- Primary CMX IP address: 192.168.1.4/24
- Secondary CMX IP address: 192.168.4.4/24
- Virtual IP address: 192.168.4.1/24
During testing, the engineer discovers that the failover fails. Which action resolves the issue?
- A. Place the primary CMX IP address and the virtual IP address in the same subnet.
- B. Place the secondary CMX IP address and the virtual IP address in different subnets.
- C. Place the primary CMX IP address and the secondary CMX IP address in the same subnet.
- D. Use a virtual IP address with CMX Layer 3 high availability.
Answer: B
NEW QUESTION # 126
When configuring a Cisco WLC, which CLI command adds a VLAN with VLAN ID of 30 to a FlexConnect group named BranchA-FCG?
- A. config flexconnect BranchA-FCG vlan 30 add
- B. config flexconnect BranchA-FCG vlan add 30
- C. config flexconnect group BranchA-FCG vlan 30 add
- D. config flexconnect group BranchA-FCG vlan add 30
Answer: D
Explanation:
NEW QUESTION # 127
A customer is concerned that their wireless network is detecting spurious threats from channels that are not being used by their wireless infrastructure. Which two technologies must they deploy? (Choose two.)
- A. monitor mode
- B. local mode with WIPS submode
- C. FlexConnect mode
- D. rogue detector mode
- E. sniffer mode with no submode
Answer: B,D
Explanation:
https://networklessons.com/cisco/ccna-200-301/cisco-wireless-ap-modes
NEW QUESTION # 128
What is the difference between PIM sparse mode and PIM dense mode?
- A. Sparse mode supports only one switch. Dense mode supports multiswitch networks.
- B. Sparse mode supports multiswitch networks. Dense mode supports only one switch.
- C. Sparse mode floods. Dense mode uses distribution trees.
- D. Sparse mode uses distribution trees. Dense mode floods.
Answer: D
Explanation:
Explanation
https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/ipmulti_pim/configuration/xe-16/imc-pim-xe-16-book/imc-te
NEW QUESTION # 129
The marketing department in a retail company has created a promotional video for the opening of a new branch store shp-GA4B6C860927AB. The video must be received by interested hosts only, over wireless multicast. What allows this feature?
- A. WMM
- B. TPC
- C. DCA
- D. WMF
Answer: D
NEW QUESTION # 130
What are two considerations when deploying a Cisco Hyperlocation? (Choose two.)
- A. The Cisco Hyperlocation feature must be enabled on the wireless LAN controller and Cisco CMX.
- B. The Cisco Hyperlocation feature must be enabled only on the wireless LAN controller.
- C. If the Cisco CMX server is a VM, a high-end VM is needed for Cisco Hyperlocation deployments.
- D. NTP configuration is available, but not recommended.
- E. After enabling Cisco Hyperlocation on Cisco CMX, the APs and the wireless LAN controller must be restarted.
Answer: A,E
NEW QUESTION # 131
A network engineer is configuring a Cisco AireOS 8.2 WLC, Cisco MSE, and Cisco PI with Cisco
3700 Series APs and Cisco Hyperlocation modules. The engineer configures and enables a WLAN with Hyperlocation. During testing, the engineer notices that the Hyperlocation module cannot be seen on the WLC. Which action resolves the issue?
- A. Add the key hash that is used to add the Hyperlocation module to the WLC.
- B. Configure the APs to be in monitor mode.
- C. Enable Hyperlocation in the Global Configuration settings of the WLC.
- D. Enable the NTP server that is connected to the Hyperlocation module.
Answer: C
Explanation:
Step 1
Choose Wireless > Access Points > Global Configuration.
Step 2
In the Hyperlocation Config Parameters section:
Check the Enable Hyperlocation check box.
Based on AP and installed module, checking the Enable Hyperlocation check box enables different location service (PRL-based or AoA-based).
https://www.cisco.com/c/en/us/td/docs/wireless/controller/8-2/config-
guide/b_cg82/b_cg82_chapter_011010.html#config-hyperlocation-
global:~:text=Check%20the%20Enable%20Hyperlocation%20check%20box.
NEW QUESTION # 132
A network engineer is implementing a wireless network and is considering deploying a single SSID for device onboarding.
Which option is a benefit of using dual SSIDs with a captive portal on the onboard SSID compared to a single SSID solution?
- A. allow multiple devices per user
- B. minimize client configuration errors
- C. limit of a single device per user
- D. restrict allowed devices types
Answer: D
NEW QUESTION # 133
An engineer completes the setup of a wo-node Cisco ISE deployment for a guest portal. When testing the portal, the engineer notices that sometimes there is a certificate CN mismatch. Which certificate type helps resolve this issue?
- A. Public-Signed Root
- B. Self-Signed Wildcard
- C. Self-Signed Standard
- D. Public-Signed SAN
Answer: B
NEW QUESTION # 134
When configuring a Cisco WLC, which CLI command adds a VLAN with VLAN ID of 30 to a FlexConnect group named BranchA-FCG?
- A. config flexconnect BranchA-FCG vlan 30 add
- B. config flexconnect BranchA-FCG vlan add 30
- C. config flexconnect group BranchA-FCG vlan 30 add
- D. config flexconnect group BranchA-FCG vlan add 30
Answer: D
Explanation:
NEW QUESTION # 135
Refer to the exhibit. An engineer is configuring a Cisco wireless LAN controller and needs wireless multicast to use the 54Mbps rates. Which action meets this requirement?
- A. Set all data rates below 54 Mbps to Disable.
- B. Set all data rates below 54 Mbps to Supported.
- C. Change the 54 Mpbs to Mandatory.
- D. Change the 24 Mpbs to Supported.
Answer: C
Explanation:
https://community.cisco.com/t5/wireless/wlc-settings-for-high-performance-cells/td- p/2298996#:~:text=The%20highest%20mandatory%20rate%20is,of%2018%20or%2024%20Mbp s
NEW QUESTION # 136
An IT administrator is managing a wireless network in which most devices are Apple iOS. A QoS issue must be addressed on the WLANs. Which configuration must be performed?
- A. Enable Fastlane globally under Wireless > Access Points > Global Configuration.
- B. Enable Fastlane under each WLAN setting.
- C. Enable WMM TSPEC/TCLAS negotiation under Wireless > Advanced.
- D. Create a new AVC Profile named AUTOQOS-AVC-PROFILE and apply to all WLANs.
Answer: B
Explanation:
https://www.cisco.com/c/dam/en/us/td/docs/wireless/controller/technotes/86/Enterprise_Best_Practices_for_iOS_devices_and_Mac_computers_on_Cisco_Wireless_LAN.pdf
NEW QUESTION # 137
For security purposes, an engineer enables CPU ACL and chooses an ACL on the Security > Access Control Lists > CPU Access Control Lists menu. Which kind of traffic does this change apply to, as soon as the change is made?
- A. wired traffic only
- B. wireless and wired traffic
- C. wireless traffic only
- D. VPN traffic
Answer: B
Explanation:
NEW QUESTION # 138
......
100% Guarantee Download 300-430 Exam Dumps PDF Q&A: https://www.actualpdf.com/300-430_exam-dumps.html
Kickstart your Career with Real Updated Questions: https://drive.google.com/open?id=1vQRUjEg-XmDVMLiFmQmTijY81V-V9gne
