[Jan-2022] Updated Aruba Certified Switching Professional (ACSP) V1 HPE6-A45 Exam Questions BUNDLE PACK
Master The HP Content HPE6-A45 EXAM DUMPS WITH GUARANTEED SUCCESS!
How to book HPE6-A45 Implementing Aruba Campus Switching solutions Exams
The registration for the HPE6-A45 Implementing Aruba Campus Switching solutions Exam follows the steps given below:
- Step 1: Visit the website Pearson VUE
- Step 2: Navigate to Certifications.
- Step 3: Search for the exam name HPE6-A45 Implementing Aruba Campus Switching solutions
- Step 4: Book the exam.
Who should take the HPE6-A45 Implementing Aruba Campus Switching solutions Exam
Individuals should pursue the HPE6-A45 exam test if they want to demonstrate their expertise and ability to access and manage data to perform queries and analyses from HPE6-A45 Implementing Aruba Campus Switching solutions Certification.
- Data managers
- Analysts
- Programmers
- Or anyone writing & interested in SAS programs
- HPE channel partners and HPE sales professionals
NEW QUESTION 89
Refer to the exhibits.
Exhibit 1
Exhibit 2
Switch-1 has a power issue that causes it to fail. When Switch-1 comes back up, endpoints lose connectivity for a few minutes. The network administrator decides to enter this command on Switch-1:
Switch-1 (config)# vlan 10 vrrp vrid 10 preempt-delay-time 120
Exhibit 2 shows the VRRP configuration just after the change. What is the effect of this change?
- A. Switch-1 and Switch-2 both become Master in their own VRRP virtual router due to the delay timer mismatch. The mismatch must be fixed.
- B. Switch-1 continues to act as it did before the preempt delay time was set. Administrators must plan additional changes to fix the issue.
- C. Switch-1 now waits to take over as Master if it fails and recovers. This should prevent the connectivity issue from occurring again.
- D. Switch-1 experiences an internal error in the VRRP process. This error causes Switch-2 to take over as Master for VLAN 2.
Answer: D
NEW QUESTION 90
Exhibit
The network administrator wants to summarize routes as much as possible in between areas. What is the correct range to specify for the router OSPF Area 2 command on Switch-2?
- A. 10.0.0.0/21
- B. 10.0.16.0/21
- C. 10.0.0.0/20
- D. 10.0.8.0/21
Answer: B
NEW QUESTION 91
A network uses MSTP. How can the AOS-Switch loop protection feature enhance this network?
- A. It can replace MSTP entirely and provide faster, more controlled convergence
- B. It can supplement MSTP on access switch edge ports to detect loops in more circumstances
- C. It can supplement MSTP on access switch uplinks to provide more control over which uplink is blocked
- D. It can replace MSTP entirely and provide better load sharing or traffic across uplinks
Answer: B
NEW QUESTION 92
Refer to the exhibits.
Exhibit 2
The network administrator configures the commands shown in Exhibit 2. Which mismatch will cause an issue?
- A. the mismatch between the key-strings in the chains for VLAN 10 and VLAN 11 on Switch-1
- B. the mismatch between the key IDs specified in chain10 and chain11 on Switch-1
- C. the mismatch between the key-strings associated with VLAN 10 on Switch-1 and on Switch-2
- D. the mismatch between the chain names associated with VLAN 11 on Switch-1 and on Switch-3
Answer: C
NEW QUESTION 93
The security plan for AOS-Switches requires protection from incoming malware traffic: generated from a worm-or virus-infected host.
Which feature should be implemented to provide the required protection?
- A. proxy ARP
- B. connection-rate filtering
- C. port security
- D. DHCP snooping
Answer: B
Explanation:
Explanation/Reference:
Reference: http://h22208.www2.hpe.com/eginfolib/networking/docs/switches/K-KA-KB/15-18/5998-
8150_access_security_guide/content/s_about_connection-rate_filtering.html
NEW QUESTION 94
Refer to the exhibit.
The network administrator wants to summarize routes as much as possible in between areas. What is the correct range to specify for the router OSPF Area 2 command on Switch-2?
- A. 10.0.0.0/21
- B. 10.0.16.0/21
- C. 10.0.0.0/20
- D. 10.0.8.0/21
Answer: B
NEW QUESTION 95
Refer to the exhibit.
Switch-1 and Switch-2 are AOS-Switches, which are iBGP peers. ISP 1 and ISP 2 advertise some routes to the same Internet destinations. Switch-1 and Switch-2 must select between these routes based on AS path length.
What is required for Switch-1 and Switch-2?
- A. iBGP synchronization enabled
- B. Multihop enabled for the connection to the iBGP neighbor
- C. eBGP and iBGP administrative distance set to the same value
- D. ECMP disabled for BGP
Answer: C
NEW QUESTION 96
An AOS-Switch implements tunneled node: Which benefit does the PAPI enhanced security key provide?
- A. It authenticates control traffic between the switch and it Mobility Controller.
- B. It validates the signature for firmware pushed to the switch dynamically.
- C. It encrypts traffic sent and received by tunneled-node endpoints.
- D. It provides an extra layer of authentication for endpoints on tunneled-node ports.
Answer: B
NEW QUESTION 97
Refer to the exhibit.
Switch-1 and Switch-2 connect on interface A23. The switches experience a connectivity issue. The network administrator sees that both switches show this interface as up. The administrator sees the output shown in the exhibit on Switch-1.
What is a typical issue that could cause this output?
- A. mismatched subnet mask on the VLAN for the link
- B. an issue with VLAN mismatch
- C. a jumbo frame mismatch
- D. asymmetric routing introduced by a routing protocol
Answer: D
NEW QUESTION 98
Refer to the exhibit.
Switch-1 runs BGP. What should the network administrator do to permit Switch-1 to establish a neighbor relationship with Router-1?
- A. Specify 192.168.1.0/30 with the network command in the BGP context.
- B. Enable BGP on VLAN 100.
- C. Configure 192.168.1.2 as a neighbor manually within the BGP context.
- D. Set the BGP AS number to 46501.
Answer: C
NEW QUESTION 99
Refer to the exhibits.
Exhibit 1
Exhibit 2
A network administrator wants to set up mirroring of traffic from port 1 on Switch-1 to port 1 on Switch-2.
Exhibit-2 shows the commands that the administrator enters. The mirroring does not work correctly.
What must the administrator do to correct the error?
- A. Re-configure the mirror endpoint command on Switch-2 with the IP addresses reversed in order.
- B. Specify the mirror endpoint command on Switch-1 and the mirror 1 remote-ip command on Switch-2.
- C. Remove the commands, and re-enter them on Switch-1 first and then on Switch-2.
- D. Change the port ID on Switch 1 to 50001, so that it is unique from the port ID on Switch-2.
Answer: A
NEW QUESTION 100
Refer to the exhibits.
Exhibit 1
Exhibit 2
In the exhibits, VLAN 20 under a device name indicates that the device is configured with that VLAN. The exhibits also indicate whether VLAN 20 is statically configured on each link, either as an untagged or a tagged VLAN. If the link has no label, VLAN 20 is not statically configured on that link.
A network administrator needs to deploy AOS-Switches that use port-based tunneled node.
The plan calls for tunneled-node endpoints to be assigned to VLAN 20 and for the Aruba Mobility Controller to handle the tunneled-node traffic at Layer 2. Which exhibit shows the correct plan for VLAN 20 in the wired infrastructure?
- A. D
- B. A
- C. C
- D. B
Answer: D
NEW QUESTION 101
Refer to the exhibits.
Exhibit 1.
Exhibit 2.
The exhibits show the current operational state for routes on Switch-3. The company wants Switch-3 to prefer the link to Switch-1 over the link to Switch-2 for all intra-area, inter-area, and external traffic.
What can the network administrator do to achieve this goal?
- A. Set the OSPF cost on VLAN 108 higher than 1 on Switch-2 and Switch-3.
- B. Set the OSPF administrative distance on Switch-2 higher than 110.
- C. Set the OSPF area type to normal on all of the switches in Area 1.
- D. Set the cost in the OSPF Area 1 stub command higher than 1 on Switch-2.
Answer: D
NEW QUESTION 102
Which situation requires an AOS-Switch interface to support MAC-based VLANs?
- A. The interface has an extended MAC ACL applied to it in the inbound direction, and it has multiple tagged VLAN assignments.
- B. The interface is configured to support Local MAC Authentication (LMA), authenticates endpoints against a non-default MAC group, and limits the address count to 1.
- C. The interface is configured to support 802.1X in user-based mode, connects to more than one endpoint at a time, and users are assigned to different dynamic VLANs.
- D. The interface has an extended MAC ACL applied to it in the outbound direction, and it uses VLAN ID as one of the criteria for rules.
Answer: A
NEW QUESTION 103
Refer to the exhibits.
Exhibit 1.
Exhibit 2.
The exhibits show the current operational state for routes on Switch-3 to send all traffic to 172.16.0.0/16 through Switch-2 during normal operation.
Which single configuration change creates the desired behavior?
- A. Set a cost of 100 in the redistribute static command on Switch-2 to change the external LSA metric.
- B. Change the OSPF external metric type to 1 on Switch-1, and set a cost of 100 on Switch-3 VLAN 104.
- C. Change the OSPF external metric type to 1 on Switch-1, and set a cost of 100 on Switch-3 VLAN 108.
- D. Set a cost of 100 in the redistribute static command on Switch-1 to change the external LSA metric.
Answer: D
NEW QUESTION 104
Which switches can be deployed in a mesh topology for backplane stacking?
- A. Aruba 2930M switches
- B. Aruba 3810 switches
- C. Aruba 2920 switches
- D. Aruba 2930F switches
Answer: B
NEW QUESTION 105
......
Pass HP HPE6-A45 Exam – Experts Are Here To Help You: https://www.actualpdf.com/HPE6-A45_exam-dumps.html
