[Dec-2021 Newly Released] 300-510 Dumps for CCNP Service Provider Certified
Updated Verified 300-510 dumps Q&As - 100% Pass
NEW QUESTION 48
Drag and drop the attributes for the BGP route selection on the left into the correct order on the right. Not all options are used.
Answer:
Explanation:
Reference:
https://www.cisco.com/c/en/us/support/docs/ip/border-gateway-protocol-bgp/13753-25.html
NEW QUESTION 49
Compare different features between OSPFv2 and OSPFv3. Drag and drop the descriptions of OSPF from the left onto the correct OSPF versions on the right.
Answer:
Explanation:
NEW QUESTION 50
Which difference should be considered when intradomain or interdomain multicast routing is implemented?
- A. Interdomain multicast routing relies on PIM-DM and intradomain multicast routing relies on PIM-SM.
- B. Interdomain multicast routing requires an IS-IS or OSPF neighbor relationship between the domains but intradomain multicast routing requires only BGP
- C. interdomain multicast routing uses BIDR-PIM to establish neighbor relationships between AS and interdomain multicast routing uses MSDP
- D. A network uses intradomain multicast routing without interdomain routing but networks that use interdomain multicast routing must also apply intradomain routing
Answer: D
NEW QUESTION 51
Which command is used to enable BIDIR-PIM under global configuration mode for Cisco IOS XE Software?
- A. multicast-routing
- B. ipv4 pim bidir-enable
- C. Ip pim bidlr-enable
- D. ip pim bidir ip
Answer: C
NEW QUESTION 52
Which two differences should be considered when deciding whether to implement to implement routing policies or route maps? (Choose two.)
- A. Route maps require an explicit deny at the end of the sequence, but routing policies have an implicit deny at the end of the program.
- B. Sequences are added after implementing a route map, but routing policies must be reconfigured when change is needed.
- C. Route maps are implemented using hierarchical policies, but routing policies must be implemented sequentially.
- D. Route policies require sequence numbers, but route maps are implemented without sequencing.
- E. Route maps are supported in Cisco 10S Software and routing policies are supported in Cisco IOS XR Software.
Answer: B,E
NEW QUESTION 53
Refer to the exhibit.
How are packets directed through the data plane when SRv6 is implemented?
- A. A stack of labels represents an ordered list of segments
- B. An ordered list of segments is encoded in a routing extension header
- C. The packet is encapsulated with a header and trailer encoding the ordered list of segments
- D. The MPLS data plane is used to push labels onto IGP routes
Answer: B
NEW QUESTION 54
Refer to the exhibit.
An engineer working for a private telecommunication company with an employee id 3977 74 814 implemented the configuration on Router 1. what is the effect of it?
- A. Router 1 sends only one best path to neighbor 192 168.1.1.
- B. Router 1 sends up to three paths to neighbor 192.168.1.1 for all routes
- C. Router 1 sends and receives multiple best paths from neighbor 192.168.1.1
- D. Router 1 receives only one best path from neighbor 192.168.1.1
Answer: C
NEW QUESTION 55
Refer to the exhibit.
After troubleshooting an OSPF adjacency issue, routers 1, 2, and 3 have formed OSPF neighbor relationships. Which statement about the configuration is true?
- A. Router 2 uses router 3 as the next hop for 192.168.0.0/24
- B. Router 2 uses router 1 as the next hop for 192.168.0.0/24
- C. Router 2 receives a Type 5 LSAs from router 1 for its connected subnets
- D. Router 2 receives a Type 7 LSAs from router 3 for its connected subnets
Answer: C
NEW QUESTION 56
Refer to the exhibits.
A network operator is troubleshooting packet loss seen from the R1 loopback interface to the R2 loopback interface over the core network. The operator is attempting to identify the next leg in the path from PE1. Which interface and label path should the operator investigate next?
- A. PE1 - Gi0/0/0/3 - forwarding label 24001
- B. PE1 - Gi0/0/0/2 - forwarding label 24002
- C. PE1 - Gi0/0/0/3 - forwarding label 24002
- D. PE1 - Gi0/0/0/2 - forwarding label 24001
Answer: A
NEW QUESTION 57
You have configured MSDP peering between two autonomous systems that pass traffic between two sites, but the peering has failed to come up.
Which task do you perform to begin troubleshooting the problem?
- A. Verify that the two MSDP peers allow asymmetric routing
- B. Verify that multicast has been disabled globally
- C. Verify that both source interfaces are reachable from both peers
- D. Verify that PIM-DM is configured on the source interface
Answer: C
NEW QUESTION 58
Refer to the exhibit
Which router does R1 install as an alternate next hop when trying to reach R3 if LFA is enabled?
- A. R2
- B. R3
- C. R5
- D. R4
Answer: A
NEW QUESTION 59
Refer to the exhibit.
Router 1 is connected to router 2 on interface TenGigE0/1. Which interface provides the alternate path to 172.16.200.9/32 when the link between router 1 and router 2 goes down?
- A. TenGigE0/2 interface provides the alternate path
- B. A primary path must be manually installed
- C. TenGigE0/1 interface provides the alternate path
- D. A backup path must be statically installed
Answer: A
NEW QUESTION 60 
Refer to the exhibit. Which task must you perform on interface g1/0/0 to complete the SSM implementation?
- A. configure IGMPv3
- B. enable CDP
- C. disable IGMP
- D. configure OSPFv3
Answer: A
Explanation:
Explanation/Reference: https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/ipmulti_pim/configuration/xe-16/imc-pim-xe-16- book/imc-ssm.html
NEW QUESTION 61
What are two differences between OSPF and IS-IS? (Choose two.)
- A. Unlike IS-IS routers, an OSPF router belongs to only one area in addition to the backbone area.
- B. OSPF elects a DR and a BDR, and IS-IS elects a DIS.
- C. OSPF uses a router ID to identify a router, and IS-IS uses a system ID.
- D. Unlike OSPF. IS-IS supports virtual links.
- E. OSPF is a link-state routing protocol, and IS-IS is a distance-vector routing protocol.
Answer: B,C
NEW QUESTION 62
Refer to the exhibit. Which LSA type is indicated by this router output?
- A. type 1 LSA
- B. type 4 LSA
- C. type 3 LSA
- D. type 2 LSA
Answer: A
NEW QUESTION 63
Refer to the exhibits.
A network operator is troubleshooting packet loss seen from the R1 loopback interface to the R2 loopback interface over the core network. The operator is attempting to identify the next leg in the path from PE1.
Which interface and label path should the operator investigate next?
- A. PE1 - Gi0/0/0/3 - forwarding label 24001
- B. PE1 - Gi0/0/0/2 - forwarding label 24002
- C. PE1 - Gi0/0/0/3 - forwarding label 24002
- D. PE1 - Gi0/0/0/2 - forwarding label 24001
Answer: A
NEW QUESTION 64
Refer to the exhibit.
Routers within the cluster are not receiving the desired prefixes. What must be done to fix the issue?
- A. Clients in that cluster must have full mesh connectivity between iBGP peers.
- B. No client-to-client must be disabled.
- C. No client-to-client reflection must be enabled.
- D. Clients in that cluster must have full mesh connectivity between eBGP peers.
Answer: A
NEW QUESTION 65
A network consultant is troubleshooting IS-IS instances to identify why a routing domains is having communication problems between the two instances. Which description of the possible cause of issues in the routing domain is true?
- A. The IS-IS "ISP" and "ISP2" instances are unrelated and unable to intercommunicate
- B. The configured IS-IS NSEL value is not allowing the routing systems to establish a neighborship
- C. The same interface cannot be advertised in two different IS-IS instances
- D. The interface mode ip router is-is
Answer: C
NEW QUESTION 66
After changing the IP address on an IOS XR router, an engineer cannot ping the new address Which step did the engineer forget to complete?
- A. roll back the configuration
- B. save the running configuration
- C. commit the configuration
- D. merge the configuration
Answer: C
NEW QUESTION 67
Refer to the exhibit.
CE1 is the gateway router into the provider network via PE1. A network operator must inject a default route into OSPF area 0. All devices inside area 0 must be able to reach PE1. Which configuration achieves this goal?
- A. Option A
- B. Option B
- C. Option C
- D. Option D
Answer: C
Explanation:
Reference:
https://www.cisco.com/c/en/us/support/docs/ip/open-shortest-path-first-ospf/47868-ospfdb9.html
NEW QUESTION 68
Refer to the exhibit
Which router does R1 install as an alternate next hop when trying to reach R3 if LFA is enabled?
- A. R2
- B. R3
- C. R5
- D. R4
Answer: A
NEW QUESTION 69
......
Test 300-510, also referred to as SPRI, is a Cisco exam that is about the execution of advanced solutions for routing for Service Providers. Someone who passes it ends up with the Cisco Certified Specialist - Service Provider Advanced Routing Implementation certificate, which is specific only to this test. The other main certificate achieved upon nailing 300-510 as well is the CCNP Service Provider.
Latest 300-510 Exam Dumps Cisco Exam from Training: https://www.actualpdf.com/300-510_exam-dumps.html
New 2021 Latest Questions 300-510 Dumps - Use Updated Cisco Exam: https://drive.google.com/open?id=1Sbkt0bqNaEtXH5T8I7ABSQytB94RcQ1B
